Accurate Technology ProScale Manual de instalación

Basic, General Purpose & Panel Mounted LCD Digital Readouts ProScale® LCD Digital Readouts OPERATION

Operation Manual for LCD Digital Readouts Page 10 of 48 Digital Readout Replacement Chart Digital Readout Type Old Number Replacement General

Manual Part # 800-1402-001 Rev E Page 11 of 48 SECTION 2 SET-UP Mounting the Digital Readout General Purpose & Basic DRO The SURFACE MOU

Operation Manual for LCD Digital Readouts Page 12 of 48 24VDC Operation The General Purpose and the Panel Mounted LCD Digital Readouts will operate

Manual Part # 800-1402-001 Rev E Page 13 of 48 The LCD The above figure illustrates all the segments available on the LCD Pressing and holding th

Operation Manual for LCD Digital Readouts Page 14 of 48 SECTION 3 OPERATION Fundamental Operation The following operations & functions app

Manual Part # 800-1402-001 Rev E Page 15 of 48 Key Functions for standard operation ON/OFF KEY Momentarily press the ON/OFF key to turn D

Operation Manual for LCD Digital Readouts Page 16 of 48 PLUS (+) & MINUS (–) KEYS Momentarily depressing the + or – key increments or

Manual Part # 800-1402-001 Rev E Page 17 of 48 Basic Functions MEASUREMENT READING DIRECTION Once the system has been put into operation,

Operation Manual for LCD Digital Readouts Page 18 of 48 DISPLAYED MEASUREMENT UNITS The measurement units displayed on the Readout when the

Manual Part # 800-1402-001 Rev E Page 19 of 48 SEGMENT OFFSET ADJUSTMENT This function applies to ProScale Model 150 & Model 250 systems and all

Operation Manual for LCD Digital Readouts Page 2 of 48 WARRANTY Accurate Technology, Inc., warrants the ProScale® Digital Measuring Systems against

Operation Manual for LCD Digital Readouts Page 20 of 48 Advanced Functions The following additional functions & operations are available on Gen

Manual Part # 800-1402-001 Rev E Page 21 of 48 SEND The Digital Readout has an output port that can be used to send measurement information to a

Operation Manual for LCD Digital Readouts Page 22 of 48 24VDC Input Input / Output Pin Common When the number 3333 is displayed in the upper left c

Manual Part # 800-1402-001 Rev E Page 23 of 48 EXTERNAL KEYPAD INPUT The multi-purpose connector on the General Purpose (GP) DRO and the circuit boa

Operation Manual for LCD Digital Readouts Page 24 of 48 SPECIAL FUNCTIONS See PROGRAMMING PARAMETERS (Pr24, 25, 26) Special Function Mode allows th

Manual Part # 800-1402-001 Rev E Page 25 of 48 Hold: F4 The Digital Readout provides a feature that allows the displayed position to be “frozen” i

Operation Manual for LCD Digital Readouts Page 26 of 48 SPECIAL FUNCTION 2: GO/NOGO PROGRAMMING PARAMETER Pr24 set to 2 In certain applications (p

Manual Part # 800-1402-001 Rev E Page 27 of 48 SPECIAL FUNCTION 3: ACCUMULATOR PROGRAMMING PARAMETER Pr24 set to 3 The Measurement Accumulator Spe

Operation Manual for LCD Digital Readouts Page 28 of 48 4. View Accumulated Total. To view the accumulated total, press the F4 key. The following

Manual Part # 800-1402-001 Rev E Page 29 of 48 SPECIAL FUNCTION 4: STATISTICS PROGRAMMING PARAMETER Pr24 set to 4 The General Purpose Digital Read

Manual Part # 800-1402-001 Rev E Page 3 of 48 Table of Contents SECTION 1 GENERAL INFORMATION ...

Operation Manual for LCD Digital Readouts Page 30 of 48 c. Press the SEND key to transmit the Maximum Measurement to the SPC port. Press the F4 k

Manual Part # 800-1402-001 Rev E Page 31 of 48 Compensation Functions NOTE: The following features are available ONLY on General Purpose Digital R

Operation Manual for LCD Digital Readouts Page 32 of 48 NON-LINEAR COMPENSATION This function is used to enhance the basic accuracy of the ProSc

Manual Part # 800-1402-001 Rev E Page 33 of 48 3. Turn the Digital Readout off. Press and hold down the DATUM key and the ON/OFF key for approxim

Operation Manual for LCD Digital Readouts Page 34 of 48 Operating the system in compensated mode. After a successful correction table has been pro

Manual Part # 800-1402-001 Rev E Page 35 of 48 Changing the Battery A low battery indicator will appear in the lower left corner of the LCD. Press a

Operation Manual for LCD Digital Readouts Page 36 of 48 Circuit Board Jumpers JP1 FACTORY USE ONLY JP2 Encoder Technology Voltage Defaul

Manual Part # 800-1402-001 Rev E Page 37 of 48 General Purpose & Basic DRO Circuit Board Panel Mount DRO Circu

Operation Manual for LCD Digital Readouts Page 38 of 48 SECTION 4 PROGRAMMING Several functions of the Digital Readouts are user programmab

Manual Part # 800-1402-001 Rev E Page 39 of 48 The Digital Readout Programming Parameters are listed below. Values in [ ] are the range of values

Operation Manual for LCD Digital Readouts Page 4 of 48 CHANGING THE BATTERY...

Operation Manual for LCD Digital Readouts Page 40 of 48 Pr 11 – Displayed Measurement Units [0 to 6, 0] This parameter controls the type of mea

Manual Part # 800-1402-001 Rev E Page 41 of 48 Pr 21 – Backlight Control [0 to 10] (Panel Mount DROs only.) If the Backlight Option is order

Operation Manual for LCD Digital Readouts Page 42 of 48 Pr 26 – Position Monitor Drift Tolerance. [.0004” to 120”, .01”] This parameter sets the a

Manual Part # 800-1402-001 Rev E Page 43 of 48 Pr 33 – Offset Addition Preset 3. Range: Any displayable position This value is added to the curren

Operation Manual for LCD Digital Readouts Page 44 of 48 Pr 37 – Programmable Output Polarity. [0 or 1] Sets the normal state of the programmable

Manual Part # 800-1402-001 Rev E Page 45 of 48 The following Programming Parameters are available only on General Purpose DROs with firmware ending

Operation Manual for LCD Digital Readouts Page 46 of 48 SECTION 5 MISCELLANEOUS Frequently Asked Questions What does no Encno Encno Encno

Manual Part # 800-1402-001 Rev E Page 47 of 48 SECTION 6 ACCESSORIES ProRF SPC ProRF allows linear measurement or position data to be tr

Operation Manual for LCD Digital Readouts Page 48 of 48 Thank you for choosing a ProScale Product, IT WAS PROUDLY MADE IN THE USA Accurate T

Manual Part # 800-1402-001 Rev E Page 5 of 48 FCC NOTICE This equipment has been tested and found to comply with the limits for a class B digital

Operation Manual for LCD Digital Readouts Page 6 of 48 SECTION 1 GENERAL INFORMATION Introduction ProScale® digital measuring systems are affordabl

Manual Part # 800-1402-001 Rev E Page 7 of 48 About This Manual This manual includes Operating and Programming information for: ProScale Basic, Gen

Operation Manual for LCD Digital Readouts Page 8 of 48 Digital Readout Specifications Linear Measurements: Display Ranges: + 999.999 in; + 399 6

Manual Part # 800-1402-001 Rev E Page 9 of 48 Digital Readout Feature Matrix This matrix is shown for comparison of features available among the sev